Leather Repair PRO
Your Dedicated Leather Care SpecialistsLeather Degreaser, Loosen up Body Oil & Grease
Product Description
Leather Degreaser is designed to remove oil, grease, accumulated body oils and oil based stains. Apply Leather Degreaser to the leather, and it dissolves the oils and transforms them into a powder that is more absorbent than the leather. Leave the powder on for about 1, 2 hours to draw the oil out. Vacuum the soiled powder or wipe it off. Repeat as needed. Typically, 2, 3 application is needed.
This is an aerosol product containing solvents. Use it with proper ventilation only. Please read and follow all safety precautions regarding this product!
When a grease or oil stain has built up gradually over several years, it cannot be removed in a few minutes. Your patience is necessary to complete the job. Also, stains left untreated for a long time may have caused additional challenges like loss of color.
Leather type for A, N & P
For the best result, clean the entire chair/sofa with Strong Cleaner after Degreasing. You may consider enhancing color by recoloring the leather for a new, beautiful look.
Once oil or grease has penetrated the grain of the leather it can be difficult to remove. Leather Degreaser draws oil out of leather and traps it on the surface where it can be easily removed. This takes time. You will need to be very patient.
1. If the stain is confined to a small area, cover any leather that doesn`t need to be treated. To do this, cut a hole approximately the size and shape of the stain in a sheet of paper and lay the paper on the leather.
2. Shake the can well.
3. Hold the can at an angle and approximately 25-30cm from the leather. Spray towards the centre of the stain, feathering the product to the outside. Make sure that droplets do not fall off the tip of the nozzle onto the leather as they may cause a ring.
4. Allow the product to dry, this may take several hours. If possible, leave to dry overnight. The degreaser goes onto the leather as a liquid and turns into a powder as it reacts with the oil in the leather.
5. Vacuum the area to remove the powder. Check that all the oil has been removed. Heavily saturated areas may require several applications. The powder can only absorb a fixed amount of oil per application.
6. Remove any residual powder using Leather Soft Cleaner (for nubuck, use the Nubuck Cleaning Cloth).
7. Dry the area with a hair dryer, then massage and knead the leather to prevent any rings from forming.
8. Re-protect the leather using the appropriate protection product.
Degreaser is an aerosol based product containing solvents. Read the safety instructions and only use the product in properly ventilated areas.
Suitable for pigmented, aniline and nubuck leather.
This is an aerosol product containing solvents. Use it with proper ventilation only. Please read and follow all safety precautions regarding this product!
When a grease or oil stain has built up gradually over several years, it cannot be removed in a few minutes. Your patience is necessary to complete the job. Also, stains left untreated for a long time may have caused additional challenges like loss of color.
CLICK HERE for video instruction of How to use Leather Degreaser"
Leather type for A, N & P
For the best result, clean the entire chair/sofa with Strong Cleaner after Degreasing. You may consider enhancing color by recoloring the leather for a new, beautiful look.
Once oil or grease has penetrated the grain of the leather it can be difficult to remove. Leather Degreaser draws oil out of leather and traps it on the surface where it can be easily removed. This takes time. You will need to be very patient.
How to Remove Oils, Greasy Stains from Leather
1. If the stain is confined to a small area, cover any leather that doesn`t need to be treated. To do this, cut a hole approximately the size and shape of the stain in a sheet of paper and lay the paper on the leather.
2. Shake the can well.
3. Hold the can at an angle and approximately 25-30cm from the leather. Spray towards the centre of the stain, feathering the product to the outside. Make sure that droplets do not fall off the tip of the nozzle onto the leather as they may cause a ring.
4. Allow the product to dry, this may take several hours. If possible, leave to dry overnight. The degreaser goes onto the leather as a liquid and turns into a powder as it reacts with the oil in the leather.
5. Vacuum the area to remove the powder. Check that all the oil has been removed. Heavily saturated areas may require several applications. The powder can only absorb a fixed amount of oil per application.
6. Remove any residual powder using Leather Soft Cleaner (for nubuck, use the Nubuck Cleaning Cloth).
7. Dry the area with a hair dryer, then massage and knead the leather to prevent any rings from forming.
8. Re-protect the leather using the appropriate protection product.
Degreaser is an aerosol based product containing solvents. Read the safety instructions and only use the product in properly ventilated areas.
Suitable for pigmented, aniline and nubuck leather.
Accessories
Strong Cleaner is a mild, water based cleaner that can be used on a most aniline and pigmented leathers. It will clean soiling as well as most water based stains. This product is used in the same manner as Leather Soft Cleaner, but its action is more intensive thanks to the greater concentration of active substances. The difference in this product is that it has twice the active cleaning ingredients. Strong Cleaner can be used on all leathers types. It is very important that you use the product in combination with a sponge to foam the product, and a cloth to wipe away the excess dirt. This product does not remove the finish from any leather that has the proper rub resistance standards. How to apply Strong Cleaner on Leather1.Pour little amount on sponge; rub into sponge, gently squeeze the sponge to create foams. Then apply to leather in a circular motion. Work cleanser gently into leather (do not scrub leather). 2. Allow a few moments for the foam to dissolve the dirt, and then remove the foam with a clean white cloth to lift dirt from leather. If your furniture is heavily soiled allow the foam to stand for 30 seconds or longer before removing it. NOTE: It is not unusual to see darkening of the leather; it will lighten again as it dries. This product is NOT a detergent, but rather a surfactant, so it needs a little extra time to work. Be patient. 3.Repeat process for stubborn soiling. For Leather Types A, P & N CLICK HERE for Video Instructions of Leather Master Strong Cleaner$10.99, 3/$30.00 | !!!Click on Color Swatch Above for Larger View!!! Select your Color. 8oz Surecoat covers apprx 10sf or one arm chair. You may find a good match on this page or you may find a good match on the auto-matched color page, Click Here for more color choices. If you are NOT sure which color to choose and would like to keep the SAME color, CUSTOM MATCH is definitely the way to go. You mail us a 1in sample. It takes us another half hour to prepare the match color, but this will make your repair or restortation job much, much easier. To accomplish a successful recoloring of leather, make sure the leather is cleaned at least two times with the SEM plastic leather prep. The leather must be dry and apply the color in light coats to achieve a professional looking finish. From the years of using the Sem sure-coat to recolor and touch up both leather and vinyl, we know that you will be pleased when you also use this product. SURE-COAT is a water based leather coating system. It offers excellent flexibility and outstanding adhesion for interior and exterior automotive, marine, and household furniture applications. You can use SURE-COAT to change or enhance the current color while maintaining the texture and look of leather, vinyl or plastic. SURE-COAT does not get brittle with age nor soften or crack within normal temperature ranges. Excellent for Protected Leather, Vinyl, and Plastic. Can apply on Aniline leather if you want to turn it into protected. It works so well because it moves right with the material -- no friction -- simply flows on. Can be Brushed or Sprayed. Easy to Use. Dries Quickly. Superior resins provide greater adhesion, flexibility and durability. Remember to order the proper cleaners and preps for the job you are doing for complete success. Get your Prep Kit Here: BASIC KIT or DELUXE KIT Instructions: * Clean with SEM Plastic/Leather PREP * If Spraying,ADD sure-coat REDUCER to thin colorant * ADD sure-coat CROSSLINKER to increase surface stains resistance the life of your recoloring job. For Type P leather. Can also use to convert Analine leather to Protected Leather. Selecting the Correct Product for your coloring situation is extremely important. Follow these 3 easy steps: 1. Identify the Leather type. P (Protected), A(Analine, N(Nubuck). Most leather has a top coat/protected finish (type P). This finish will still show the grain but forms a coating on the leather. Paint or Dye is used on top coat finishes. 2. Select the color. Look up the color as appropriate in the furniture or auto color charts. You may find a good match on this page or you may find a good match on the auto-matched color page, Here. . Slight variations from your existing color is expected because of your computer screen settings and the age, conditions of your leather. 3. Select the product that matches your need. If we don't have your color, just send us a sample and we will match it for you. May we suggest our popular leather recoloring kit? It's the quick and easy way to get everything you need. We will send you Detailed Step-by-Step Instructions and Video Instructions (if available) after your purchase. * 8oz covers apprx one chair * 32oz covers apprx one sofa, loveseat, and a small chair $23.99 |
Questions? Email: support@LeatherRepairPro.com